[Tutorial] How to fix an Infinix Note 2 X600 totally dead after flashing wrong firmware
[Tutorial] How to fix an Infinix Note 2 X600 totally dead after flashing wrong firmware
17-02-2016, 08:55 PM
!!! PLEASE READ THIS ENTIRE POST BEFORE PROCEEDING !!!
this tutorial applies to all infinx note 2 X600 and it is not require a specified firmware do it when your phone totally dead (no boot, not detected by pc)
WARNING
Do it at your own risk, i'm not responsible for any bricks you may obtain. Please follow the thread rules and steps and everything will be gravy. Remember, select the right firmware for your phone
Requirements
- A hardware knowledge
- Infinix drivers and xflash tools : http://adf.ly/1X55aL
- A windows PC
- The right firmware for your phone " notice for 532 or 533 board "
X600 H 532 A1 L : http://adf.ly/1X4Uuu
X600 H 533 A1 L : http://adf.ly/1X4Vhu
X600 H 533 B1 L : http://adf.ly/1X4VLT
- If you don't know your board number it will be written on the board as you will see in the pictures
Steps on how to fix an Infinix Note 2 X600 totally dead after flashing wrong firmware
- Install the drivers
- Identify your board number for the right firmware
![[Image: How-to-fix-an-Infinix-Note-2-X600-totall...ware-1.jpg]](https://www.hovatek.com/blog/bpyeki/uploads/2017/10/How-to-fix-an-Infinix-Note-2-X600-totally-dead-after-flashing-wrong-firmware-1.jpg)
- After confirming that you have the right firmware, start xflash tool and load the scatter file then click on start
- Only connect the socket in the picture below, then connect the usb cable from the PC to the dead phone. (The PC must not detect the phone at this point)
![[Image: How-to-fix-an-Infinix-Note-2-X600-totall...ware-2.jpg]](https://www.hovatek.com/blog/bpyeki/uploads/2017/10/How-to-fix-an-Infinix-Note-2-X600-totally-dead-after-flashing-wrong-firmware-2.jpg)
- Now, make a jumper by connecting a thin piece of wire between the "ground" and the "force boot" pinout.
![[Image: How-to-fix-an-Infinix-Note-2-X600-totall...ware-3.jpg]](https://www.hovatek.com/blog/bpyeki/uploads/2017/10/How-to-fix-an-Infinix-Note-2-X600-totally-dead-after-flashing-wrong-firmware-3.jpg)
![[Image: How-to-fix-an-Infinix-Note-2-X600-totall...ware-4.jpg]](https://www.hovatek.com/blog/bpyeki/uploads/2017/10/How-to-fix-an-Infinix-Note-2-X600-totally-dead-after-flashing-wrong-firmware-4.jpg)
- Once your jumper is successful, you'll hear the the connection sound on your PC. The PC will recognize your phone and the xflash tool will begin flashing.
Contributors:
mhmyasser
thanks to "satin" for the pictures
thanks to "hovatek"
This post was last modified: 30-10-2017, 04:26 PM by X3non.
18-02-2016, 12:25 PM
For Tecno D5 users in the same shoes, follow the guide @ https://www.hovatek.com/forum/thread-11802.html
Learn MediaTek, Unisoc / Spreadtrum (SPD) and Qualcomm Software Repairs @ https://www.hovatek.com/training
Note!
We have a reply schedule for Forum Support. Please try Private Support if you can't wait.
19-02-2016, 06:54 AM
whoa its work detect my device but somehow i cannot flash it because seems like it always unplug after its plug.. its like the unplug sound hearing right after its detected it... and flash processing take forever
edit : woooaaaa its works you just keep doing the part when 2 jumper conected one time... just keep push it till the flashtool goes into green flash load thank hovatex thanx TS you are really life saver
This post was last modified: 19-02-2016, 07:20 AM by gayus.
19-02-2016, 11:24 AM
Learn MediaTek, Unisoc / Spreadtrum (SPD) and Qualcomm Software Repairs @ https://www.hovatek.com/training
Note!
We have a reply schedule for Forum Support. Please try Private Support if you can't wait.
19-02-2016, 09:33 PM
(19-02-2016, 07:36 PM)storm52 finally did the jumper thingy pc now detects the phone but am facing error 3178
Screenshot of the error message please
Learn MediaTek, Unisoc / Spreadtrum (SPD) and Qualcomm Software Repairs @ https://www.hovatek.com/training
Note!
We have a reply schedule for Forum Support. Please try Private Support if you can't wait.
19-02-2016, 10:20 PM
(19-02-2016, 07:36 PM)storm52 finally did the jumper thingy pc now detects the phone but am facing error 3178
did you download and install the drivers from my link just make sure about that and everything will be fine
and read this line carefully
" just make the jumper for one touch don't keep them connected"
This post was last modified: 19-02-2016, 10:22 PM by mhmyasser.
Users browsing this thread:
1 Guest(s)
1 Guest(s)
Users browsing this thread:
1 Guest(s)
1 Guest(s)
