[Downloads] Tecno POP 3 BB2 Stock ROM | Firmware and Component Files
[Downloads] Tecno POP 3 BB2 Stock ROM | Firmware and Component Files
25-06-2021, 10:17 AM
(24-06-2021, 07:59 PM)robel pop TECNO POP 3 twrp or any custom recovery
see https://www.hovatek.com/forum/thread-21839.html
Learn MediaTek, Unisoc / Spreadtrum (SPD) and Qualcomm Software Repairs @ https://www.hovatek.com/training
Note!
We have a reply schedule for Forum Support. Please try Private Support if you can't wait.
01-07-2021, 05:59 PM
I have installed proper driver proper driver for device . what shall I do.
This post was last modified: 01-07-2021, 06:10 PM by robelasche.
02-07-2021, 09:44 AM
(01-07-2021, 05:59 PM)robelasche I was trying to backup firmware of tecno pop3 but when I USB plug after switch of phone it continuously change the port then back to battery charging.
I have installed proper driver proper driver for device . what shall I do.
Ensure that you're using the custom DA for this model and also try using a different USB cable
If you still have problems then create a new thread for this device issue by clicking "Ask Question" at the top
Learn MediaTek, Unisoc / Spreadtrum (SPD) and Qualcomm Software Repairs @ https://www.hovatek.com/training
Note!
We have a reply schedule for Forum Support. Please try Private Support if you can't wait.
04-07-2021, 06:54 AM
(01-07-2021, 05:59 PM)robelasche I was trying to backup firmware of tecno pop3 but when I USB plug after switch of phone it continuously change the port then back to battery charging.
I have installed proper driver proper driver for device . what shall I do.
I have also noticed that this problem also occurs when one presses the wrong boot key EG volume- instead of pressing the volume+ key. It has happened to me on many phones and on Tecno BB2 as well. After disconnecting, removing the battery and reinserting it back, now connecting the phone to the PC while pressing the correct boot key has always done the job. And when talking of installing proper device drivers, do you mean the Tecno POP3 drivers or the Mediatec Vcom drivers? I because I'm sure you should have installed the latter.
2. Have you checked if the device is being detected by the computer in windows device manager? To check if the drivers are well installed, launch Device manager, Go to a section called Other devices, connect your device while holding the volume+ button and see if the device appears. If it does not appear, consider manually installing Mediatek Vcom drivers.
This post was last modified: 04-07-2021, 07:08 AM by Dilone61.
21-07-2021, 10:26 AM
(04-07-2021, 06:54 AM)Dilone61(01-07-2021, 05:59 PM)robelasche I was trying to backup firmware of tecno pop3 but when I USB plug after switch of phone it continuously change the port then back to battery charging.
I have installed proper driver proper driver for device . what shall I do.
I have also noticed that this problem also occurs when one presses the wrong boot key EG volume- instead of pressing the volume+ key. It has happened to me on many phones and on Tecno BB2 as well. After disconnecting, removing the battery and reinserting it back, now connecting the phone to the PC while pressing the correct boot key has always done the job. And when talking of installing proper device drivers, do you mean the Tecno POP3 drivers or the Mediatec Vcom drivers? I because I'm sure you should have installed the latter.
2. Have you checked if the device is being detected by the computer in windows device manager? To check if the drivers are well installed, launch Device manager, Go to a section called Other devices, connect your device while holding the volume+ button and see if the device appears. If it does not appear, consider manually installing Mediatek Vcom drivers.
what is correct boot key for Tecno BB2
22-07-2021, 10:59 AM
(21-07-2021, 10:26 AM)robelasche what is correct boot key for Tecno BB2
You could find out for yourself by trying out different key combos starting with the easiest i.e only vol down or only vol up
Learn MediaTek, Unisoc / Spreadtrum (SPD) and Qualcomm Software Repairs @ https://www.hovatek.com/training
Note!
We have a reply schedule for Forum Support. Please try Private Support if you can't wait.
24-07-2021, 06:56 PM
(02-07-2021, 09:44 AM)X3non(01-07-2021, 05:59 PM)robelasche I was trying to backup firmware of tecno pop3 but when I USB plug after switch of phone it continuously change the port then back to battery charging.
I have installed proper driver proper driver for device . what shall I do.
Ensure that you're using the custom DA for this model and also try using a different USB cable
If you still have problems then create a new thread for this device issue by clicking "Ask Question" at the top
thanks very much the problem was from Default DA.
26-07-2021, 02:33 PM
(25-06-2021, 10:17 AM)X3nonthanks so much(24-06-2021, 07:59 PM)robel pop TECNO POP 3 twrp or any custom recovery
see https://www.hovatek.com/forum/thread-21839.html
25-08-2021, 01:43 PM
(25-08-2021, 02:30 AM)efedi val I flashed this tecno pop3 firmware but it lost the display what will I do
create a new thread for this by clicking "ask question" at the top
in the new thread, state the build number of your device before you flashed it
Learn MediaTek, Unisoc / Spreadtrum (SPD) and Qualcomm Software Repairs @ https://www.hovatek.com/training
Note!
We have a reply schedule for Forum Support. Please try Private Support if you can't wait.
Users browsing this thread:
1 Guest(s)
1 Guest(s)
Users browsing this thread:
1 Guest(s)
1 Guest(s)
