[Downloads] Tecno MTK Secure Boot Download Agent (DA) loader files
[Downloads] Tecno MTK Secure Boot Download Agent (DA) loader files
18-02-2019, 10:43 AM
(16-02-2019, 11:23 PM)coach comm Tecno CF7K DA FILE PLEASE!
try CF7 DA on page 1 of this thread
Learn MediaTek, Unisoc / Spreadtrum (SPD) and Qualcomm Software Repairs @ https://www.hovatek.com/training
Note!
We have a reply schedule for Forum Support. Please try Private Support if you can't wait.
18-02-2019, 10:45 AM
(18-02-2019, 09:35 AM)TanzirIslam Tecno Camon isky 2 da file please
check your PM
Learn MediaTek, Unisoc / Spreadtrum (SPD) and Qualcomm Software Repairs @ https://www.hovatek.com/training
Note!
We have a reply schedule for Forum Support. Please try Private Support if you can't wait.
18-02-2019, 03:49 PM
(18-02-2019, 01:23 PM)Chip Please, need Da File for Tecno POP 1s Pro (F4 Pro), thanks)
check your PM
Learn MediaTek, Unisoc / Spreadtrum (SPD) and Qualcomm Software Repairs @ https://www.hovatek.com/training
Note!
We have a reply schedule for Forum Support. Please try Private Support if you can't wait.
23-02-2019, 03:18 PM
(23-02-2019, 12:22 PM)Victor De Abreu Tecno T350
this model doesnt require a custom DA file
if you have any problems with the phone then create a new thread so we'll focus on it
see https://www.hovatek.com/forum/thread-514.html for how to create a thread
Learn MediaTek, Unisoc / Spreadtrum (SPD) and Qualcomm Software Repairs @ https://www.hovatek.com/training
Note!
We have a reply schedule for Forum Support. Please try Private Support if you can't wait.
25-02-2019, 09:32 AM
(28-12-2018, 07:31 PM)hovatek(28-12-2018, 12:57 PM)kaktuszz Need Da File for Tecno POP 1s Pro (F4 Pro), thanks)
I've sent you a PM
I also need a DA file for Tecno POP 1s Pro (F4 Pro).
When I try to flash it, flash tooll gives:
error: status_sec_auth_file_needed (0xc0030012)
When trying to flash it, SWD_AfterSales issues:
DA connection failed! Status da hash mistmach 100%
CM2MT2 when trying to connect gives:
Infinity-Box Chinese Miracle MediaTek Service Module [MTK] v2.05
Load IDBase v123080 Ok!
Operation: Identify [v2.05]
1. Make sure the device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...
PTFN: MediaTek USB Port (COM7)
MODE: BOOTROM
PORT: 7
Waiting BOOT ack ...
BROM: Skip ACK verify
BROM: Init BROM
BROM init passed!
CHIP: MT6739, SBID: 0x8A00, HWVR: 0xCB00, SWVR: 0x0002
TYPE: MODERN RAPHAEL
BROM: SecLevel: 0x000000E5
BROM: SecMode: SBC + SDA + ARB
BROM: BOOTROM
MODE: TECNO: BASE_SECURE | Manual: Disabled
BROM: ARB: ACTIVE: LOG: F0: 102B 0000 F3: 0000 0000 V0: 0000 0000 [0001]
BROM: SOCID: 518360DA74F6C8EF8364889A308C587ABB1E12205DFA7D97F8A7C13832B3B4F8
AGENT: Look for suitable BootChain in DA ...
AGENT: MTK_AllInOne_DA.bin
AGENT: Found MT6739
AGENT: MTK_DOWNLOAD_AGENT
BROM: Sending 1st DA ...
BROM: 0x00007017: DA SEND ERROR!
ERROR: SECURE BOOT: SLA REQUIRED IN BROM MODE!
INFO: BROM Level: CERT / AUTH required! Try a boot device in PRELOADER mode with select PL / PL_CRYPTO / SWSEC type!
Error: Fail to init protocol!
Remove battery, cable. Check cable / connection / driver! Check SW hint! Repeat operation!
Reconnect Power / Cable!
Thanks in advance.
Users browsing this thread:
2 Guest(s)
2 Guest(s)
Users browsing this thread:
2 Guest(s)
2 Guest(s)