Huawei E5785Lh-23c unlock-possible?
Huawei E5785Lh-23c unlock-possible?
12-09-2019, 01:24 PM
(12-09-2019, 07:37 AM)A1ex037 Hello everyone,
Can anyone confirm that is possible to unlock Huawei E5785Lh-23c? I haven't been able to find any useful information about this model.
Thanks.
might be possible, its v4 algo
you need to find USBloader or USBlsafe for your model and modified firmware to flash after flashing and boot points
whats the current firmware / software version of your device?
Learn MediaTek, Unisoc / Spreadtrum (SPD) and Qualcomm Software Repairs @ https://www.hovatek.com/training
Note!
We have a reply schedule for Forum Support. Please try Private Support if you can't wait.
13-09-2019, 01:36 PM
(12-09-2019, 05:17 PM)A1ex037 Hello,
Thanks for answering. This is what I can see vie web interface.
Hardware version: CL1E5785SM05
Software version: 21.189.61.00.532
Web UI version: 21.100.44.00.532
If you have any idea, I'm willing to try it.
usblsafe @ https://mega.nz/#!SToilKZR!Jqvew1DSHYe5d...rrRxYC5CZ4
use USBlsafe instead of usbloader within the compressed file in the link below
try the tool & instructions @ https://mega.nz/#!zf4zEAJZ!Dw7jTC7spPd0D...qS3ZZmrq9E
note that dismantling void warranty and you should only proceed if you are aware of the risks of attempting to flash usbloader/firmware
This post was last modified: 13-09-2019, 05:30 PM by X3non.
Learn MediaTek, Unisoc / Spreadtrum (SPD) and Qualcomm Software Repairs @ https://www.hovatek.com/training
Note!
We have a reply schedule for Forum Support. Please try Private Support if you can't wait.
13-09-2019, 09:40 PM
X3non, thanks for answering. I have followed this method to the letter. It fails at some point (not sure what's wrong, but it looks like the firmware is not updated). This is what I'm getting when I run Unlock:
> bin\adb connect 192.168.8.1:5555
* daemon not running. starting it now *
* daemon started successfully *
unable to connect to 192.168.8.1:5555
> bin\adb push bin\balong-nvtool /
error: device not found
> bin\adb shell chmod 777 /balong-nvtool
error: device not found
> bin\adb shell /balong-nvtool -m 8268:01:00:00:00:02:00:00:00:0A:00:00:00
error: device not found
> bin\adb shell rm /balong-nvtool
error: device not found
ÅÑαѺáúαπº¬á πßΓα«⌐ßΓóá...
> bin\adb shell "echo -en 'AT^RESET\r' > /dev/appvcom1"
error: device not found
Éáí«Γá ß¬α¿»Γá ºáóÑαΦÑ¡á. ì᪼¿ΓÑ ½εíπε ¬½áó¿Φπ
Device information shows the same info as before:
Hardware version: CL1E5785SM05
Software version: 21.189.61.00.532
Web UI version: 21.100.44.00.532
Drivers are correctly installed, Balong performs OK (everything is showed in DevMgr as it is supposed to).
During firmware flash, I noticed a bunch of question marks, but I assume that they are language related. Maybe I'm wrong there?
Any advice?
14-09-2019, 09:38 AM
(13-09-2019, 09:40 PM)A1ex037 X3non, thanks for answering. I have followed this method to the letter. It fails at some point (not sure what's wrong, but it looks like the firmware is not updated). This is what I'm getting when I run Unlock:
...Any advice?
unlock will not work cause the firmware didn't get flashed, only proceed once you notice the change in software version
retry the entire procedure from the beginning
Learn MediaTek, Unisoc / Spreadtrum (SPD) and Qualcomm Software Repairs @ https://www.hovatek.com/training
Note!
We have a reply schedule for Forum Support. Please try Private Support if you can't wait.
14-09-2019, 12:19 PM
Thanks.
This post was last modified: 14-09-2019, 12:19 PM by A1ex037.
Attached Files
14-09-2019, 04:25 PM
(14-09-2019, 12:19 PM)A1ex037 I did it several times, but I always end up with the same result. Take a look at the attached image.
Thanks.
try running go.cmd without admin rights
let me know the outcome
Learn MediaTek, Unisoc / Spreadtrum (SPD) and Qualcomm Software Repairs @ https://www.hovatek.com/training
Note!
We have a reply schedule for Forum Support. Please try Private Support if you can't wait.
16-09-2019, 11:46 PM
(14-09-2019, 06:02 PM)A1ex037 Result is the same. I have tried the same procedure on clean Windows 7 machine with identical drivers.
try this firmware @ https://mega.nz/#!HbYWjCZI!HzUg6i7y4hKwV...RDuDsowSCg
ensure to copy the bin file from this into the firmware folder then delete the existing bin file before running go.cmd
Learn MediaTek, Unisoc / Spreadtrum (SPD) and Qualcomm Software Repairs @ https://www.hovatek.com/training
Note!
We have a reply schedule for Forum Support. Please try Private Support if you can't wait.
Users browsing this thread:
1 Guest(s)
1 Guest(s)
Users browsing this thread:
1 Guest(s)
1 Guest(s)