Hello, please I have an infinix x6516 device that is bricked . First it use to power on stays on infinix logo and goes off. Refuses to enter recovery mode.
I had to use cm2 spd3 to factory reset it but nothing happened.
I downloaded it firmware to flash it and it refuse to turn.
Downloaded other firmware but nothing happened. Finally I downloaded I used the exact version and nothing .
I try using research download tool but it says not supported.
Below is the log report from cm2 before flash device and the build number on this log is the last file used on the device.
This is the first device info
log report for x6516
. [2024-06-07_02-20-55 C:\InfinityBox\CM2SP3\CM2SP3.exe] ===
Wait...
S/N: 00290727C0 v0161
Chinese Miracle II - SP3 Service Tool v2.26
Init log engine...
Ok
Build directories tree...
Backup files: C:\InfinityBox\CM2SP3\backup\
Backup files: 0 dirs: 0
Build device list...
SP3 boot-pack v1.07 2024-03-04
Ok
Ready
Selected: Hyundai 10LC1 [Boot FireFly]
[FF] protocol may be SLOW, for flash Read/Write use [FDL]
Selected: Hyundai 10LC1 [Boot FireFly]
[FF] protocol may be SLOW, for flash Read/Write use [FDL]
Selected: Infinix Hot-10i [Boot FireFly]
mmc
[FF] protocol may be SLOW, for flash Read/Write use [FDL]
Selected: Infinix X6516 [Boot FireFly]
mmc
[FF] protocol may be SLOW, for flash Read/Write use [FDL]
Operation: Connect [sc9863a Boot FireFly] [v2.26]
Wait...
- Power device Off
- Connect cable [remember Vol+ | Vol-] [remember Test-Point]
Waiting for device...
Device found
PTFN: SPRD U2S Diag (COM6) vid 0x1782 pid 0x4D00
boot: SPRD3
boot iLoader...
Ok
start iLoader...
Ok
Handshake...
Ok
boot xLoader...
Ok
start FireFly...
Ok
Loader exec
Ok
Dev UID: 82d180f2a1dda7111ac0525466e988a24cf90e2054efea8888b30c03adc6b155
get storage info...
EMMC
CID: D6010341334135363112210B6928AA29
crc Ok
Vendor: Foresee OEM: 259 ID: 413341353631 [A3A561] PRV: 0x12
Serial: 554395944 0x210B6928
MM/YY: 10/2023
CSD: D0FFFF329F5903FFFFFFFFEF964000FF
temp_write_protect: False
perm_write_protect: False
wp_group: 0x10 en 0x01
EXTCSD rev1.8 EMMC 5.1
FW: 12
ERASE_GROUP_DEF: 0x0400
BOOT_BUS_WIDTH: 0x00
PARTITION_CONFIG: 0x08
RST_N_FUNCTION: 0x01
PART_S_COMPLETED: False
BOOT0/BOOT1 size: 0x400000 4.00 Mb
RPMB size: 0x1000000 16.00 Mb
WP_GRP_SIZE: 0x800000 8.00 Mb
Size: Market 64 Gb Actual 0xE67800000 57.62 Gb
EOL: Status: Normal: Less than 80% reserved blocks used
EOL_A: SLC status: 0% - 10% used
EOL_B: MLC status: Not defined
read extcsd...
Ok
extcsd stored: C:\InfinityBox\CM2SP3\backup\ext_csd\sc9863_82d180f2a1dda711_extcsd_00D6-Foresee_A3A561_5.1_2024-06-07.bin
Verify config values...
Socket Error # 11001
Host not found.
Can it flash without battery not plugged.
The last file flash to the device is the exact build number of device and still not turn. Well I give this file a try
This post was last modified: 23-06-2024, 08:19 PM by jazzykenn.
