Samsung Mediattek A04e dead

4

26-03-2024, 09:20 AM

#1

While I was flashing the Samsung A04e which was at the point at Android version 14 the latest update, Now when I was trying to flash it through odin, it was giving an error that its not possible to rollback this device.
Later on I installed sp flash tool and wiped the full EMMC, now my phone is getting detected as an usb port com 8.
Nothing more then that, no bootloader, no recovery and it's not even getting shown in odin, so that I can flash the new stock rom, in sp flash tool I tried flashing emmc file's but failed.

maxpayne
Intern

4,201

26-03-2024, 04:39 PM

#2

(26-03-2024, 09:20 AM)Shadypsychopath While I was flashing the Samsung A04e which was at the point at Android version 14 the latest update, Now when I was trying to flash it through odin, it was giving an error that its not possible to rollback this device.
Later on I installed sp flash tool and wiped the full EMMC, now my phone is getting detected as an usb port com 8.
Nothing more then that, no bootloader, no recovery and it's not even getting shown in odin, so that I can flash the new stock rom, in sp flash tool I tried flashing emmc file's but failed.

What is the phone's bit version and that of the scatter firmware you're trying to use?

Note!
We have a reply schedule for Free Support. Please upgrade to Private Support if you can't wait.

Shadypsychopath
Newbie

4

27-03-2024, 01:53 PM

#3

Bit version is U4, the latest update is that I intalled mtkclient and connected the phone,
.Port - Device detected Smile

Preloader - CPU: MT6765/MT8768t(Helio P35/G35)
Preloader - HW version: 0x0
Preloader - WDT: 0x10007000
Preloader - Uart: 0x11002000
Preloader - Brom payload addr: 0x100a00
Preloader - DA payload addr: 0x201000
Preloader - CQ_DMA addr: 0x10212000
Preloader - Var1: 0x25
Preloader - Disabling Watchdog...
Preloader - HW code: 0x766
Preloader - Target config: 0xe5
Preloader - SBC enabled: True
Preloader - SLA enabled: False
Preloader - DAA enabled: True
Preloader - SWJTAG enabled: True
Preloader - EPP_PARAM at 0x600 after EMMC_BOOT/SDMMC_BOOT: False
Preloader - Root cert required: False
Preloader - Mem read auth: True
Preloader - Mem write auth: True
Preloader - Cmd 0xC8 blocked: True
Preloader - Get Target info
Preloader - BROM mode detected.
Preloader - HW subcode: 0x8a00
Preloader - HW Ver: 0xca00
Preloader - SW Ver: 0x0
Preloader - ME_ID: A7D828803EDDED6ED2E1438B0DB98E7B
Preloader - SOC_ID: 2004491F749543B49584751E34C0D97042A47BC71B8C9C0A4EE2BDA2A45C938C
DA_handler - Device is protected.
DA_handler - Device is in BROM-Mode. Bypassing security.
PLTools - Loading payload from mt6765_payload.bin, 0x264 bytes
Exploitation - Kamakiri Run
Exploitation - Done sending payload...
PLTools - Successfully sent payload: D:\mtkclient-main\mtkclient\payloads\mt6765_payload.bin
Port - Device detected Smile

DA_handler
DA_handler - [LIB]: Device is in BROM mode. No preloader given, trying to dump preloader from ram.
DA_handler
DA_handler - [LIB]: Failed to dump preloader from ram, provide a valid one via --preloader option
DAXFlash - Uploading xflash stage 1 from MTK_DA_V5.bin
DAXFlash - Successfully uploaded stage 1, jumping ..
Preloader - Jumping to 0x200000
Preloader - Jumping to 0x200000: ok.
DAXFlash - Successfully received DA sync
DAXFlash - DRAM config needed for : 150100345836324d
DAXFlash - No preloader given. Searching for preloader
DAXFlash
DAXFlash - [LIB]: No preloader given. Operation may fail due to missing dram setup.
DAXFlash - Uploading stage 2...
DAXFlash
DAXFlash - [LIB]: Error on sending data: DA hash mismatch (0xc0070004)
DAXFlash
DAXFlash - [LIB]: Error on booting to da (xflash)

This is the log getting, I tried disabling sbc and daa through, mtk sec disabler it it says done, but actually it's like that only.

Shadypsychopath
Newbie

4

27-03-2024, 02:32 PM

#4

Preloader - CPU: MT6765/MT8768t(Helio P35/G35)
Preloader - HW version: 0x0
Preloader - WDT: 0x10007000
Preloader - Uart: 0x11002000
Preloader - Brom payload addr: 0x100a00
Preloader - DA payload addr: 0x201000
Preloader - CQ_DMA addr: 0x10212000
Preloader - Var1: 0x25
Preloader - Disabling Watchdog...
Preloader - HW code: 0x766
Preloader - Target config: 0xe5
Preloader - SBC enabled: True
Preloader - SLA enabled: False
Preloader - DAA enabled: True
Preloader - SWJTAG enabled: True
Preloader - EPP_PARAM at 0x600 after EMMC_BOOT/SDMMC_BOOT: False
Preloader - Root cert required: False
Preloader - Mem read auth: True
Preloader - Mem write auth: True
Preloader - Cmd 0xC8 blocked: True
Preloader - Get Target info
Preloader - BROM mode detected.
Preloader - HW subcode: 0x8a00
Preloader - HW Ver: 0xca00
Preloader - SW Ver: 0x0
Preloader - ME_ID: A7D828803EDDED6ED2E1438B0DB98E7B
Preloader - SOC_ID: 2004491F749543B49584751E34C0D97042A47BC71B8C9C0A4EE2BDA2A45C938C
Main - Getting target info...
Preloader - Target config: 0xe5
Preloader - SBC enabled: True
Preloader - SLA enabled: False
Preloader - DAA enabled: True
Preloader - SWJTAG enabled: True
Preloader - EPP_PARAM at 0x600 after EMMC_BOOT/SDMMC_BOOT: False
Preloader - Root cert required: False
Preloader - Mem read auth: True
Preloader - Mem write auth: True
Preloader - Cmd 0xC8 blocked: True

This is the log when I read it through mediatek client

maxpayne
Intern

4,201

04-04-2024, 10:08 AM

#5

(27-03-2024, 01:53 PM)Shadypsychopath Bit version is U4, the latest update is that I intalled mtkclient and connected the phone,

The latest for the model is Bit 6 but you've still not answered my question
What is the phone's Bit version and the scatter firmware's bit version?
For mtk client, try adding the preloader flag using the preloader from the firmware

Note!
We have a reply schedule for Free Support. Please upgrade to Private Support if you can't wait.

View a Printable Version

Users browsing this thread:
1 Guest(s)

Find us

Call us

Mail us

Useful Links

Actions