Join us on Tl   Wh

Hovatek Forum MOBILE Android Bricked phone

Bricked phone

Bricked phone

rayvon
rayvon
rayvon
Junior Member
15
28-09-2021, 04:00 PM
#1



I was able to flash my camon 12 cc7 with sp flash tool but I omitted tkv and dtbo partition file that had secured boot.
The rest were ok because it showed download was ok but the my main problem is that the phone won"t power on
I don know if it is because of the omitted partition.Any advice please/solution(the phone had been bricked earlier on before flashing)
hovatek
hovatek
hovatek
Administrator
49,753
29-09-2021, 08:57 AM
#2
(28-09-2021, 04:00 PM)rayvon I was able to flash my camon 12 cc7 with sp flash tool but I omitted tkv and dtbo partition file that had secured boot.
The rest were ok because it showed download was ok but the my main problem is that the phone won"t power on
I don know if it is because of the omitted partition.Any advice please/solution(the phone had been bricked earlier on before flashing)

unable to power on, meaning that it is totally dead right?
can't be due to tkv and dtbo, instead it's either the phone is stuck at flash mode or you flash the wrong firmware
disconnect / reconnect the battery of the device then confirm if it can power on or not
Khaliil
Khaliil
Khaliil
Junior Member
27
29-09-2021, 10:37 AM
#3
(28-09-2021, 04:00 PM)rayvon I was able to flash my camon 12 cc7 with sp flash tool but I omitted tkv and dtbo partition file that had secured boot.
The rest were ok because it showed download was ok but the my main problem is that the phone won"t power on
I don know if it is because of the omitted partition.Any advice please/solution(the phone had been bricked earlier on before flashing)

Same thing happened to me when i locked the bootloader, couldn't flash, untick both partitions and flash, unlock bootloader, restart and you can flash all again

Sent from my TECNO LE7 using Hovatek Mobile
rayvon
rayvon
rayvon
Junior Member
15
29-09-2021, 01:41 PM
#4
(29-09-2021, 08:57 AM)X3non
(28-09-2021, 04:00 PM)rayvon I was able to flash my camon 12 cc7 with sp flash tool but I omitted tkv and dtbo partition file that had secured boot.
The rest were ok because it showed download was ok but the my main problem is that the phone won"t power on
I don know if it is because of the omitted partition.Any advice please/solution(the phone had been bricked earlier on before flashing)

unable to power on, meaning that it is totally dead right?
can't be due to tkv and dtbo, instead it's either the phone is stuck at flash mode or you flash the wrong firmware
disconnect / reconnect the battery of the device then confirm if it can power on or not

Yeah it's dead
I have disconnected / reconnected the battery but it doesn't power on then the I downloaded
the full firmware for camon 12 cc7 from Hovatek that's what I used to flash it; I might not think it's wrong firmware
Attached Files
.png
2021-09-29.png
Size: 128.7 KB / Downloads: 1
.png
2021-09-29 (1).png
Size: 130.57 KB / Downloads: 1
rayvon
rayvon
rayvon
Junior Member
15
29-09-2021, 02:07 PM
#5



I also did a readback using sp flash tool and obtained a full ROM Dump from Wwr mtk tool and saved from my pc so I have two full firmware one from hovatek and another from Wwr tool
hovatek
hovatek
hovatek
Administrator
49,753
30-09-2021, 10:45 AM
#6
(29-09-2021, 02:07 PM)rayvon I also did a readback using sp flash tool and obtained a full ROM Dump from Wwr mtk tool and saved from my pc so I have two full firmware one from hovatek and another from Wwr tool

this readback was made from this very device when it was still able to power on?
if yes, have you tried flashing it back? or you can check the build number from the recovery.img of the backup ; see method 7 @ https://www.hovatek.com/forum/thread-16005.html
rayvon
rayvon
rayvon
Junior Member
15
30-09-2021, 02:26 PM
#7
(30-09-2021, 10:45 AM)X3non
(29-09-2021, 02:07 PM)rayvon I also did a readback using sp flash tool and obtained a full ROM Dump from Wwr mtk tool and saved from my pc so I have two full firmware one from hovatek and another from Wwr tool

this readback was made from this very device when it was still able to power on?
if yes, have you tried flashing it back? or you can check the build number from the recovery.img of the backup ; see method 7 @ https://www.hovatek.com/forum/thread-16005.html

Nop i did a readback after it was bricked (after I flashed the other firmware from hovatek )
rayvon
rayvon
rayvon
Junior Member
15
01-10-2021, 02:21 PM
#8
(30-09-2021, 02:26 PM)rayvon
(30-09-2021, 10:45 AM)X3non
(29-09-2021, 02:07 PM)rayvon I also did a readback using sp flash tool and obtained a full ROM Dump from Wwr mtk tool and saved from my pc so I have two full firmware one from hovatek and another from Wwr tool

this readback was made from this very device when it was still able to power on?
if yes, have you tried flashing it back? or you can check the build number from the recovery.img of the backup ; see method 7 @ https://www.hovatek.com/forum/thread-16005.html

Nop i did a readback after it was bricked (after I flashed the other firmware from hovatek )
can it be resolved in any means possible?please advice
hovatek
hovatek
hovatek
Administrator
49,753
02-10-2021, 08:44 AM
#9
(30-09-2021, 02:26 PM)rayvon Nop i did a readback after it was bricked (after I flashed the other firmware from hovatek )

use method 7 @ https://www.hovatek.com/forum/thread-16005.html
confirm if the build number from the backup you made matches the one from the firmware you flashed


(01-10-2021, 02:21 PM)rayvon can it be resolved in any means possible?please advice

if the device is still dead even after disconnecting / reconnecting the battery then you need to search for and try a different firmware build other than what we have listed here
you could try the build @ [ Login to download]
Users browsing this thread:
 1 Guest(s)
Users browsing this thread:
 1 Guest(s)
Join us
WhTlYt