Code 10 VCOM Preloader drivers error
Code 10 VCOM Preloader drivers error
(05-03-2020, 11:26 AM)Jaephoenix How can I flash my Umidigi One? I have been having Device cannot start error code 10 whenever I install the VCOM Preloader drivers. And SP flash tool cannot recognize my device
(05-03-2020, 12:07 PM)innageeThank you. I have done all the above. Same problem persisted.(05-03-2020, 11:26 AM)Jaephoenix How can I flash my Umidigi One? I have been having Device cannot start error code 10 whenever I install the VCOM Preloader drivers. And SP flash tool cannot recognize my device
disable drivers signature verification, follow the guide @ https://www.hovatek.com/forum/thread-752.html
then install VCOM drivers using https://www.hovatek.com/forum/thread-440.html , you'll still get error 10 but this time PC can detect it.
Also before flashing, could you tell us what's wrong with the phone and how the problem began?
(05-03-2020, 12:11 PM)Jaephoenix Thank you. I have done all the above. Same problem persisted.
The phone just went blank while I was chatting with someone on Whatsapp and charging. It doesn't power on or boot to recovery, but the charging LED comes on when charging or connected to PC
(05-03-2020, 09:21 PM)X3nonIts a non-removable battery. All latest phones are(05-03-2020, 12:11 PM)Jaephoenix Thank you. I have done all the above. Same problem persisted.
The phone just went blank while I was chatting with someone on Whatsapp and charging. It doesn't power on or boot to recovery, but the charging LED comes on when charging or connected to PC
disconnect / reconnect the battery of the device then allow to charge for a while before you retry powering it on if not then retry flashing the firmware
(06-03-2020, 06:14 AM)Jaephoenix(05-03-2020, 09:21 PM)X3nonIts a non-removable battery. All latest phones are(05-03-2020, 12:11 PM)Jaephoenix Thank you. I have done all the above. Same problem persisted.
The phone just went blank while I was chatting with someone on Whatsapp and charging. It doesn't power on or boot to recovery, but the charging LED comes on when charging or connected to PC
disconnect / reconnect the battery of the device then allow to charge for a while before you retry powering it on if not then retry flashing the firmware
(06-03-2020, 11:25 AM)innageeHa guy. No be everybody get that expertise. Besides I don't have the hardwares like tiny screwdriver to open my phone(06-03-2020, 06:14 AM)Jaephoenix(05-03-2020, 09:21 PM)X3nonIts a non-removable battery. All latest phones are(05-03-2020, 12:11 PM)Jaephoenix Thank you. I have done all the above. Same problem persisted.
The phone just went blank while I was chatting with someone on Whatsapp and charging. It doesn't power on or boot to recovery, but the charging LED comes on when charging or connected to PC
disconnect / reconnect the battery of the device then allow to charge for a while before you retry powering it on if not then retry flashing the firmware
you’ll have to loosen the phone and disconnect/reconnect the battery.
(06-03-2020, 11:43 AM)Jaephoenix Ha guy. No be everybody get that expertise. Besides I don't have the hardwares like tiny screwdriver to open my phone
(06-03-2020, 12:26 PM)X3nonI waited til the battery drained, still the PC didnt recognize it(06-03-2020, 11:43 AM)Jaephoenix Ha guy. No be everybody get that expertise. Besides I don't have the hardwares like tiny screwdriver to open my phone
either you look for screwdriver or someone who has OR you wait for two week or less depending on the size of the battery, hopefully the battery of the device will drain completely then you charge it for a few mins and retry flashing
(09-03-2020, 07:36 PM)Jaephoenix(06-03-2020, 12:26 PM)X3nonI waited til the battery drained, still the PC didnt recognize it(06-03-2020, 11:43 AM)Jaephoenix Ha guy. No be everybody get that expertise. Besides I don't have the hardwares like tiny screwdriver to open my phone
either you look for screwdriver or someone who has OR you wait for two week or less depending on the size of the battery, hopefully the battery of the device will drain completely then you charge it for a few mins and retry flashing