Mediatek drivers for windows 10

Jane1
Junior Member

28

08-03-2019, 09:17 AM

#1

Where can I download working MediaTek drivers for windows 10?
When is it necessary to disable Windows 10 64 bit driver signature enforcement?
Thanks

hovatek
Administrator

49,767

08-03-2019, 03:44 PM

#2

(08-03-2019, 09:17 AM)Jane1 Where can I download working MediaTek drivers for windows 10?
When is it necessary to disable Windows 10 64 bit driver signature enforcement?
Thanks

download vcom signed drivers @ https://www.hovatek.com/forum/thread-16640.html
installation procedure is similar to the guide @ https://www.hovatek.com/forum/thread-440.html only there's no need to disable drivers signature before installing

Jane1
Junior Member

28

08-03-2019, 06:35 PM

#3

Thank you for your help.
I tried to install few of them but all I installed ended with the error:

This device cannot start. (Code 10)

The specified request is not a valid operation for the target device.

Where can be a problem?
Thanks

hovatek
Administrator

49,767

08-03-2019, 11:26 PM

#4

(08-03-2019, 06:35 PM)Jane1 Thank you for your help.
I tried to install few of them but all I installed ended with the error:

This device cannot start. (Code 10)

The specified request is not a valid operation for the target device.

Where can be a problem?
Thanks

Code 10 errors shouldn't be something to worry about.
Try using the Mediatek tools you intend to use

Note!
We have a reply schedule for Free Support. Please upgrade to Private Support if you can't wait.

Jane1
Junior Member

28

09-03-2019, 09:26 AM

#5

Thanks for your reply.
But CODE 10 is a problem.

Here is the log from Infinity box

Infinity-Box Chinese Miracle MediaTek Service Module [ MTK ] v2.05

Load IDBase v123080 Ok!

Operation : Identify [ v2.05 ]

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek PreLoader USB VCOM (Android) (COM36)
MODE : PRELOADER PORT
PORT : 36
Error : Failed to open port!

Error : Fail to init protocol!

I tried to install those drivers on different computers( with WIndows 10) and received the same error code 10 .
Anyone tried to install that drivers on windows 10 successfuly?

Thanks

This post was last modified: 09-03-2019, 08:02 PM by Jane1.

Jane1
Junior Member

28

11-03-2019, 07:29 AM

#6

I can not install Mediatek drivers - it finishes with CODE 10 error.

I use Windos 10 Home
Version 1803

I tried to install those drivers on different computers( with WIndows 10) and received the same error code 10 .

Anyone tried to install that drivers on windows 10 successfuly?

Must I install any service pack on WIndows 10 so that the drivers will work?

Thanks

hovatek
Administrator

49,767

11-03-2019, 11:40 AM

#7

(11-03-2019, 07:29 AM)Jane1 I can not install Mediatek drivers - it finishes with CODE 10 error.
I use Windos 10 Home
Version 1803
I tried to install those drivers on different computers( with WIndows 10) and received the same error code 10 .
Anyone tried to install that drivers on windows 10 successfuly?
Must I install any service pack on WIndows 10 so that the drivers will work?

Thanks

code 10 doesn't mean installation didn't work, it just means you installed an unsigned driver and there's nothing wrong with that

Jane1
Junior Member

28

11-03-2019, 01:05 PM

#8

Thanks for your reply.
And what drivers should I download from https://www.hovatek.com/forum/thread-16640.html ?
I downloaded from that drivers marked as Mediatek USB VCOM Drivers Signed (all MT**** devices) .
Are they correct ( are they really signed) then?
Thanks

shankar1790
Senior Member

474

11-03-2019, 01:50 PM

#9

(11-03-2019, 01:05 PM)Jane1 Thanks for your reply.
And what drivers should I download from https://www.hovatek.com/forum/thread-16640.html ?
I downloaded from that drivers marked as Mediatek USB VCOM Drivers Signed (all MT**** devices) .
Are they correct ( are they really signed) then?
Thanks

Just boot win10 in test mode and connect your phone to pc and check device manager if it is showing any mediatek preloader or usb port driver under port section.

Jane1
Junior Member

28

11-03-2019, 03:06 PM

#10

.
I started WIndows in TEST mode, and tried to install the drivers again . But it finished in the same way - CODE 10.
Any idea how to continue?Thanks

View a Printable Version

Users browsing this thread:
1 Guest(s)

Find us

Call us

Mail us

Useful Links

Actions