Flash cloned tecno AL86
Flash cloned tecno AL86
(05-02-2019, 05:24 PM)EMMANUS Images of the 'chinese' screen will help a lot.Screenshot
Try holding volume buttons one at a time and inserting the usb cable.
(05-02-2019, 05:19 PM)mencoronaldo I've downloaded tecno AL86 file but the device is not detected by my PC (starts charging immediately). When I connect to PC while pressing the power + vol up with it without ba3, it displays some kind of Chinese warning & "Android" will appear under "other devices" (device manager).
I've tried different combos to boot to recovery without any luck
How can I get my PC to detect it; I've already installed mtk USB drivers
Sent from my TECNO KA7 using Hovatek Mobile
(06-02-2019, 09:17 AM)X3non(05-02-2019, 05:19 PM)mencoronaldo
I've downloaded tecno AL86 file but the device is not detected by my PC (starts charging immediately). When I connect to PC while pressing the power + vol up with it without ba3, it displays some kind of Chinese warning & "Android" will appear under "other devices" (device manager).
I've tried different combos to boot to recovery without any luck
How can I get my PC to detect it; I've already installed mtk USB drivers
Sent from my TECNO KA7 using Hovatek Mobile
before you begin flashing, what is wrong with the phone and how did the problem begin?
do you have a backup of the current firmware? yes, even if the phone is soft-bricked
(06-02-2019, 10:48 AM)mencoronaldo(06-02-2019, 09:17 AM)X3non(05-02-2019, 05:19 PM)mencoronaldo I've downloaded tecno AL86 file but the device is not detected by my PC (starts charging immediately). When I connect to PC while pressing the power + vol up with it without ba3, it displays some kind of Chinese warning & "Android" will appear under "other devices" (device manager).
I've tried different combos to boot to recovery without any luck
How can I get my PC to detect it; I've already installed mtk USB drivers
Sent from my TECNO KA7 using Hovatek Mobile
before you begin flashing, what is wrong with the phone and how did the problem begin?
do you have a backup of the current firmware? yes, even if the phone is soft-bricked
The phone is stuck at boot loop.
It happened after charging the phone. I have a backup I downloaded from this forum.
Sent from my TECNO KA7 using Hovatek Mobile
(06-02-2019, 05:33 PM)mencoronaldo My problem is that the phone is not connecting at all
Sent from my TECNO KA7 using Hovatek Mobile
(05-02-2019, 07:12 PM)mencoronaldo(05-02-2019, 05:24 PM)EMMANUS Images of the 'chinese' screen will help a lot.Screenshot
Try holding volume buttons one at a time and inserting the usb cable.
http://imgur.com/gallery/TTY7w8k
Holding the vol- had no effect, holding vol+ brings up the first image, when pressed the second time it brings the second image, while the vol- will reboot the device
Sent from my TECNO KA7 using Hovatek Mobile
(08-02-2019, 02:32 PM)EMMANUS(05-02-2019, 07:12 PM)mencoronaldo
(05-02-2019, 05:24 PM)EMMANUS
Images of the 'chinese' screen will help a lot.
Try holding volume buttons one at a time and inserting the usb cable.
Screenshot
http://imgur.com/gallery/TTY7w8k
Holding the vol- had no effect, holding vol+ brings up the first image, when pressed the second time it brings the second image, while the vol- will reboot the device
Sent from my TECNO KA7 using Hovatek Mobile
The image you posted is either of fastboot or download mode, and that is most likely originally a coolpad device.
Connect the phone to your PC when you set it to the second screen and check what it is detected as on device manager.
Also try random key combinations to boot to recovery.
You can also peel the label in the battery compartment to see if there is another label under it.
