[Downloads] Gionee m6 GN8003 firmware with Gapps and french language

[Zid China]

Hi everyone,

I've just bought a Gionee m6 GN8003 helio p10 (...) and the firmware is chinese with a lots of bloatwares and chineses apps. i have tried to install gapps via CWM recovery by puting the gapps.zip in the internal storage with no sd card inserted .but i got this error: 

Code:

E: can't mount /storage/sdcard

-Even though the data is mounted (i checked and rebooted so many time from recovery to recovery but no luck, always the error above).
so i tried google installer.apk and i installed google services and play store but got an error:

Code:

unfortunately, google services has stopped.

- tried different google installer apk but no luck.
-tried to make a flashable zip using the system.img and boot.img with assyyeed but got an error : system.img can't created,the operation can't continue.
-i didn't find ant TWRP recovery so i used CWM as mentioned above.

-also tried to flash my gionee m6 Gn8003 with more than 7 version of sp_flash_tools including the one inside the frimeware package, even though all the drivers are correctely installed  and pressing the volume down while connecting the device, but always getting the below error:

Code:

status_sec_auth_file_needed

-i have been looking in the internet for an international firmware with google services and multi language(at least EN/FR)  but with no luck.

i need your help because i'm unable to use the phone without play store and google services.
-yesterday i got an ota update did that the phone rebooted into CWM recovery and stopped there with error ( E: can't mount /storage/sdcard ) and never rebooted to system , when i press reboot system or power off/on the phone always reboot to CWM recovery. stuck forever there.

if anyone has any information that could help me i would be very gratefull.

if you need any information, let me know.


Thank you so much for helping me

[X3non]

Hi everyone,
...
if you need any information, let me know.


Thank you so much for helping me

Gionee M6 is quite trick when it comes to having the correct firmware
are you 100% sure the firmware you have is the right firmware? 
if it is, then load this auth file at https://forum.xda-developers.com/attachm...1495907203 into SPft before selecting the scatter file
if you are not sure, then only flash boot, recovery and system ONLY

[Zid China]

First, Thank you so much for your time and your efforts, i really  appreciate it.
Second, i'm not sure about the firmware but i was looking for an international one with Google services. so i checked only the boot.img as you told me and after i failed i checked everything and tried also with (download only, upgrade,format all+ download) , also tried 2 version of sp_flash_tools, and this time i attached the auth_file you posted in the authentification place, a new error appears (see error bellow).

Code:

STAUS_BROOM_CMD_FAIL

-I changed the usb port and cable but same error.

any ideas, thank you again for your time.

[X3non]

...
-I changed the usb port and cable but same error.

any ideas, thank you again for your time.

remember i said to tick only boot, recovery and system not boot alone
for the new SPft error, you need to post full error message [better still attach a screenshot]

[Zid China]

please see the error (see attachment please)

thank you for helping, any ideas ?

[hovatek]

Hi everyone,
...
- tried different google installer apk but no luck.
-tried to make a flashable zip using the system.img and boot.img with assyyeed but got an error : system.img can't created,the operation can't continue.
-i didn't find ant TWRP recovery so i used CWM as mentioned above.
...
Thank you so much for helping me

From what you've typed, your phone first needs to be unbricked before talking of Gapps.
Gionee M6 could be quite tricky to flash because it needs a specific download agent in SP flash tool.
1. Where did you get that auth file you used in sp flash tool?
2. Try using SP flash tool V5.1624 and Wwr @ https://www.hovatek.com/forum/thread-21970.html to dump the firmware. You need to find out the Build Number

[Zid China]

Thank you so much for your help.
1-i got the auth file from the link on the second post in this page.
2-my phone is hard bricked now ( no fastboot , no recovery ).
any ideas to unbricked it? i'm frustrated right now?
thank you for trying!

[freshtyt]

Thank you so much for your help.
1-i got the auth file from the link on the second post in this page.
2-my phone is hard bricked now ( no fastboot , no recovery ).
any ideas to unbricked it? i'm frustrated right now?
thank you for trying!

hardbricked means the phone is dead and it doesn't seem like your phone is totally dead
perform the firmware dump as @hovatek suggested to obtain the build number

[Zid China]

Thank you so much for your help.
1-i got the auth file from the link on the second post in this page.
2-my phone is hard bricked now ( no fastboot , no recovery ).
any ideas to unbricked it? i'm frustrated right now?
thank you for trying!

hardbricked means the phone is dead and it doesn't seem like your phone is totally dead
perform the firmware dump as @hovatek suggested to obtain the build number

unfortunately i can't backup my gionee m6 using the miracleBox because when i connect the phone , the phone keep disconecting and connection every 2 seconds.
so the miracle box doesn't recognize my phone, all the driver are installed though.

what to do?

[freshtyt]

unfortunately i can't backup my gionee m6 using the miracleBox because when i connect the phone , the phone keep disconecting and connection every 2 seconds.
so the miracle box doesn't recognize my phone, all the driver are installed though.

what to do?

there's no mention of miracle box anywhere, check the link in @hovatek's reply for the tool and guide to use