[phonesurgeon]

I wanted to remove password from it but couldn't.
What I did to remove the pattern
•i tried reset code with miracle crack but the phone still had the lock on it.
I tried hard reset still the phone asked for password.

So i decided to flash the phone, unfortunately I flashed x557 firmware instead of x557 lite and the phone went completely dead.

I downloaded the x557 lite firmware but sp flashtool demanded format before i flash but after formatting... Phone cant be detected again.

•I have uninstalled mtk drivers with (USB DEVIEW) and installed the driver again but nothing
I disconnected the battery cable(battery not removable) and connected the usb but nothing.

Please Note: I have installed mobile go and that software detects the mode every phone i connect is in.
With mtk if it shows(MTK BLU DASH) i know i cant im in preloader for mode.
Usually when its not ther it displays MTK X91x

In device mananager if mobile go shows. MTK.BLU DASH it'll display Mediatek preloader next to the its divers(mediatek preloader)

Now its displaying MTK M91x and device menu shows USB Serial Device
Regardless the combination i use that's all im getting.

I have used only sp flash tool v5.1644, 5.1532 and 5.1708

The error i get is S FT ENABLE DRAM FAILED(4032)



Sent from my GT-N7100 using Tapatalk

[X3non]

I wanted to remove password from it but couldn't.
What I did to remove the pattern
...

Sent from my GT-N7100 using Tapatalk

was the factory reset you performed successful without errors?
and does the PC make any sound when you connect the phone?

[phonesurgeon]

The factory reset was successful without any errors

Yes it does and it detects the phone as USB serial in drivers menu.

Sent from my GT-N7100 using Tapatalk

[xerxes]

The factory reset was successful without any errors

Yes it does and it detects the phone as USB serial in drivers menu.

Sent from my GT-N7100 using Tapatalk

Retry connecting the phone while holding vol down, up or both the vol keys.

[phonesurgeon]

I have tried all the volumes, changed the usb cable. Still all I get is USB serial

Sent from my GT-N7100 using Tapatalk

[X3non]

I have tried all the volumes, changed the usb cable. Still all I get is USB serial

Sent from my GT-N7100 using Tapatalk

if factory reset was successful and you're sure the phone was still passworded then its likely the emmc chip is damaged
try updating the drivers of the phone using the guide at https://www.hovatek.com/forum/thread-16839.html

[hovatek]

I have tried all the volumes, changed the usb cable. Still all I get is USB serial

Sent from my GT-N7100 using Tapatalk

4032 is a mismatch error and could mean 1 of these things

1. Driver issue (rare)
2. You're holding volume down button when connecting  (which you shouldn't)
3. Incompatible firmware
4. Damaged emmc chip

Try updating the phone's drivers (what it gets detected as) as x3non suggested in his last post. If it persists then maybe its an emmc issue. You should also consider trying the first firmware you accidentally flashed

[phonesurgeon]

I have tried all the volumes, changed the usb cable. Still all I get is USB serial

Sent from my GT-N7100 using Tapatalk

4032 is a mismatch error and could mean 1 of these things

1. Driver issue (rare)
2. You're holding volume down button when connecting  (which you shouldn't)
3. Incompatible firmware
4. Damaged emmc chip

Try updating the phone's drivers (what it gets detected as) as x3non suggested in his last post. If it persists then maybe its an emmc issue. You should also consider trying the first firmware you accidentally flashed
[/quote]
Your last sentence made me go back to the firmware i accidentally flashed.
It is the same as the new one im trying to flash but now it can... The preloader is coming except(usb serial device)

Sent from my GT-N7100 using Tapatalk

[hovatek]

Your last sentence made me go back to the firmware i accidentally flashed.
It is the same as the new one im trying to flash but now it can... The preloader is coming except(usb serial device)

Sent from my GT-N7100 using Tapatalk

maybe its an emmc chip issue. Try the other options i'd listed