Hovatek Forum
ITEL A32F WHITE SCREEN AFTER FLASH - Printable Version

+- Hovatek Forum (https://www.hovatek.com/forum)
+-- Forum: MOBILE PHONES HELP SECTION (https://www.hovatek.com/forum/forum-75.html)
+--- Forum: Android (https://www.hovatek.com/forum/forum-76.html)
+--- Thread: ITEL A32F WHITE SCREEN AFTER FLASH (/thread-30506.html)



ITEL A32F WHITE SCREEN AFTER FLASH - ricardo ngong - 19-10-2019

Please help me i i had privacy password in itel a32f so i downloaded the firmwaree from hoveatek after flash phone power on with white screen. please i need solution or firmware to soft this issue.

Code:
logs 1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 7 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6580
BB_CPU_NME : [MediaTek] MT6580_S00
BB_CPU_EXT : 0xCA00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer  : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x94
NAND Flash : NOT INSTALLED
eMMC Flash : 150100464E36324D4203E43F9AD6A5D1
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x15 , OEM : 0100
[eMMC] : FLASH_INF : [SAMSUNG] , BM26N
[eMMC] : FLASH_CID : 150100464E36324D4203E43F9AD6A5D1
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00080000
[eMMC] : FLASH_LEN : 0x00000001D2000000
[eMMC] : FLASH_UCP : 7456 MiB [eMMC 8 GiB]
DEV RID    : 0xFD7832695FECC6BB7A638F376D78AD55
INT RAM    : 0x00020000
EXT RAM    : 0x40000000 [1 GiB]
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

ScatCFG : BaseBand : MT6752 , Project : a32f , Storage : EMMC
Setting : Flash Pre-Erase (Safe) : Enabled
Setting : AFF verify :  Enabled
Setting : HW verify :  Enabled

BL : Check HW compatibility
BL : BBID supported by BootLoader!
BL : Check eMMC compatibility
BL : eMMC supported by BootLoader!

BL : BatteryLevel : 3825 mV
BL : BatteryLevel Ok

BL : Flash Pre-Erase
Total blocks to Erase : 1
Erase : 0x0000000004C80000-0x00000001CC300000
Flash Pre-Erase Done, time used : 00:00:00

SecCfg Passed , 1799
BMT remark not need. Will skip
Sending Preloader ...
Use : preloader_a32f.bin
Preloader Sent , Init passed
SecCfg Passed , 1799
PartCount : FFFFFFFF
PartErr : Not initialized , will update PMT now ...
Repartition Done!
Use FLN Mode

Processing : Flash Write
Flash now : LK
Image Flash Ok
Flash now : LK2
Image Flash Ok
Flash now : BOOT
Image Flash Ok
Flash now : RECOVERY
Image Flash Ok
Flash now : LOGO
Image Flash Ok
Flash now : ODMDTBO
Image Flash Ok
Flash now : VENDOR
Image Flash Ok
Flash now : TEE1
Image Flash Ok
Flash now : TEE2
Image Flash Ok
Flash now : SECRO
Image Flash Ok
Flash now : SYSTEM
Image Flash Ok
Flash now : CACHE
Image Flash Ok
Flash now : USERDATA
Image Flash Ok
Flash Write Done, time used : 00:04:09

Processing : Verify
Verify Passed : LK
Verify Passed : LK2
Verify Passed : BOOT
Verify Passed : RECOVERY
Verify Passed : LOGO
Verify Passed : ODMDTBO
Verify Passed : VENDOR
Verify Passed : TEE1
Verify Passed : TEE2
Verify Passed : SECRO
Verify Passed : SYSTEM
Verify Passed : CACHE
Verify Passed : USERDATA
Data Verify Done, time used : 00:01:03

Update Mirror PMT
Update Done!

Update RomInfo done

Done!
Elapsed: 00:05:26
Reconnect Power/Cable!



ITEL A32F WHITE SCREEN AFTER FLASH - xerxes - 20-10-2019

(19-10-2019, 07:50 PM)ricardo ngong Wrote:  Please help me i i had privacy password in itel a32f so i downloaded the firmwaree from hoveatek after flash phone power on with white screen. please i need solution or firmware to soft this issue.

Code:
logs 1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 7 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6580
BB_CPU_NME : [MediaTek] MT6580_S00
BB_CPU_EXT : 0xCA00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer  : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x94
NAND Flash : NOT INSTALLED
eMMC Flash : 150100464E36324D4203E43F9AD6A5D1
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x15 , OEM : 0100
[eMMC] : FLASH_INF : [SAMSUNG] , BM26N
[eMMC] : FLASH_CID : 150100464E36324D4203E43F9AD6A5D1
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00080000
[eMMC] : FLASH_LEN : 0x00000001D2000000
[eMMC] : FLASH_UCP : 7456 MiB [eMMC 8 GiB]
DEV RID    : 0xFD7832695FECC6BB7A638F376D78AD55
INT RAM    : 0x00020000
EXT RAM    : 0x40000000 [1 GiB]
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

ScatCFG : BaseBand : MT6752 , Project : a32f , Storage : EMMC
Setting : Flash Pre-Erase (Safe) : Enabled
Setting : AFF verify :  Enabled
Setting : HW verify :  Enabled

BL : Check HW compatibility
BL : BBID supported by BootLoader!
BL : Check eMMC compatibility
BL : eMMC supported by BootLoader!

BL : BatteryLevel : 3825 mV
BL : BatteryLevel Ok

BL : Flash Pre-Erase
Total blocks to Erase : 1
Erase : 0x0000000004C80000-0x00000001CC300000
Flash Pre-Erase Done, time used : 00:00:00

SecCfg Passed , 1799
BMT remark not need. Will skip
Sending Preloader ...
Use : preloader_a32f.bin
Preloader Sent , Init passed
SecCfg Passed , 1799
PartCount : FFFFFFFF
PartErr : Not initialized , will update PMT now ...
Repartition Done!
Use FLN Mode

Processing : Flash Write
Flash now : LK
Image Flash Ok
Flash now : LK2
Image Flash Ok
Flash now : BOOT
Image Flash Ok
Flash now : RECOVERY
Image Flash Ok
Flash now : LOGO
Image Flash Ok
Flash now : ODMDTBO
Image Flash Ok
Flash now : VENDOR
Image Flash Ok
Flash now : TEE1
Image Flash Ok
Flash now : TEE2
Image Flash Ok
Flash now : SECRO
Image Flash Ok
Flash now : SYSTEM
Image Flash Ok
Flash now : CACHE
Image Flash Ok
Flash now : USERDATA
Image Flash Ok
Flash Write Done, time used : 00:04:09

Processing : Verify
Verify Passed : LK
Verify Passed : LK2
Verify Passed : BOOT
Verify Passed : RECOVERY
Verify Passed : LOGO
Verify Passed : ODMDTBO
Verify Passed : VENDOR
Verify Passed : TEE1
Verify Passed : TEE2
Verify Passed : SECRO
Verify Passed : SYSTEM
Verify Passed : CACHE
Verify Passed : USERDATA
Data Verify Done, time used : 00:01:03

Update Mirror PMT
Update Done!

Update RomInfo done

Done!
Elapsed: 00:05:26
Reconnect Power/Cable!

Did you take note of the phone’s build no before flashing it?
Try flashing lk.bin of a different firmware @ https://www.hovatek.com/forum/thread-23178.html .