Hovatek Online Twrp builder issue

2

07-09-2024, 05:25 PM

#1

Hi i am harshith and i would like to seek a guidance and to solve an issue with the twrp builder. I tried to build a twrp for a device named tecno spark 8 pro (kg8) which has a mediatek helio g85 processor and there were few unofficial twrp out there which didn't seem to work so i just built one using twrp builder by providing it with the boot.img as my device firmware doesn't have a seperate recovery partition nor vendor partition and also I did add up the touch driver and after that the build was successful and i also successfully flashed it to my device and after when I went on to try it, it did just boot up fine but the touch didn't seem to work unless untill i reboot it twice or thrice and nor did the otg work and after when I tried to flash it to the ramdisk it always ends up getting failed when I looked up through a thread in XDA found out that u should wipe up the data and reboot back to recovery and when I tried that again the touch got lost and i tried building it multiple times but it always fails to falsh to the ramdisk i just hope and request to please help me with it

Thankyou

hovatek
Administrator

49,850

07-09-2024, 07:23 PM

#2

(07-09-2024, 05:25 PM)harshithr566@gmail.com Hi i am harshith and i would like to seek a guidance and to solve an issue with the twrp builder. I tried to build a twrp for a ..

Thankyou

We're aware of this issue on some devices and are testing on devices with similar specs to yours.
For clarity, please list out the exact steps you took in TWRP

Note!
We have a reply schedule for Free Support. Please upgrade to Private Support if you can't wait.

harshithr566@gmail.com
Newbie

2

08-09-2024, 03:40 AM

#3

Ok so the first thing was once the twrp was built I tried to boot it using that fastboot boot.img and found out that it doesn't work on mtk devices as they don't support it so i had to flash it directly to the boot partition using the cmd fastboot flash boot and then fastboot reboot recovery. The twrp booted successfully without any issues but after that the main issue which arised was touch so i tried to connect an otg cable but twrp didn't seem to detect it and also I hadn't specified the touch drivers I restarted the device again and again and in the end touch seemed to work and once that was done I taught I should rebuild by specifying the touch drivers and once it was rebuilt I had the same issue so i continued ignoring it but restarting few times then I went to flash the twrp to ramdisk and the new temp boot img was also ready and when I tried to flash it up it ended in a error and found out that since my device was encrypted j couldn't flash it so i just formatted and the reformated to ext4 and when I tried it the new boot img was acquired successfully without any error or failed message like last time and when tried to flash it up the device came up with a message something like /dev/block/mmcblkop28 is locked and can't read and failed to flash again also the storage device isn't visible on windows while in twrp even after formatting it if you need further attachments I will flash the twrp once again and provide them to you

hovatek
Administrator

49,850

10-09-2024, 01:05 PM

#4

(08-09-2024, 03:40 AM)harshithr566@gmail.com ..acquired successfully without any error or failed message like last time and when tried to flash it up the device came up with a message something like /dev/block/mmcblkop28 is locked and can't read and failed to flash again also the storage device isn't visible on windows while in twrp even after formatting it if you need further attachments I will flash the twrp once again and provide them to you

OK.
Please fill this form @ https://forms.gle/cQxn9u7DEmzYktug9

Note!
We have a reply schedule for Free Support. Please upgrade to Private Support if you can't wait.

yhr391
Newbie

3

24-03-2025, 08:12 AM

#5

(08-09-2024, 03:40 AM)harshithr566@gmail.com Ok so the first thing was once the twrp was built I tried to boot it using that fastboot boot.img and found out that it doesn't work on mtk devices as they don't support it so i had to flash it directly to the boot partition using the cmd fastboot flash boot and then fastboot reboot recovery. The twrp booted successfully without any issues but after that the main issue which arised was touch so i tried to connect an otg cable but twrp didn't seem to detect it and also I hadn't specified the touch drivers I restarted the device again and again and in the end touch seemed to work and once that was done I taught I should rebuild by specifying the touch drivers and once it was rebuilt I had the same issue so i continued ignoring it but restarting few times then I went to flash the twrp to ramdisk and the new temp boot img was also ready and when I tried to flash it up it ended in a error and found out that since my device was encrypted j couldn't flash it so i just formatted and the reformated to ext4 and when I tried it the new boot img was acquired successfully without any error or failed message like last time and when tried to flash it up the device came up with a message something like /dev/block/mmcblkop28 is locked and can't read and failed to flash again also the storage device isn't visible on windows while in twrp even after formatting it if you need further attachments I will flash the twrp once again and provide them to you

I have working twrp for this device.

maxpayne
Intern

4,288

28-03-2025, 12:17 PM

#6

(24-03-2025, 08:12 AM)yhr391 I have working twrp for this device.

Why not share the link

Note!
We have a reply schedule for Free Support. Please upgrade to Private Support if you can't wait.

yhr391
Newbie

3

28-03-2025, 12:25 PM

#7

(28-03-2025, 12:17 PM)maxpayne
(24-03-2025, 08:12 AM)yhr391 I have working twrp for this device.

Why not share the link

https://xdaforums.com/t/recovery-unoffic...n.4716174/

View a Printable Version

Users browsing this thread:
1 Guest(s)

Find us

Call us

Mail us

Useful Links

Actions