TECNO Camon 15 Air bricked/dead completely

[Please help] TECNO Camon 15 Air bricked/dead completely

Mikesew1320
Junior Member

30

03-11-2023, 05:07 AM

#1

I replaced new battery and unlocked bootloader and flashed vbmeta.img and custom recovery.img and I noticed that I dont have Magisk zip on my sdcard and just hit the reboot button and now the device boot into fastboot mode directly and now put the magisk zip on my sdcard and flashed both the images above and unplugged the device. when I try to boot into Recovery, I cant b/c device dead. I used Miracle box 2.82 thunder from here to flash the device.

When I try to flash the whole device ROM, It showing me CPU dead or....

Tried with NCK Pro Box Loader here it just stuck after detecting device and show error after a couple of minutes and Transssion Tool with factory signed firmware and its showing BROM BINDED error.

REmember that I used custom DA File on Miracle and NCK Pro Box Loader!

Unplugged the device battery and tried to flash then..... Miracle kills itself when it reach flashing super partition! Auto exit.

I asked my friend and he said it may be emmc corruption and I should use emmc fixer or replace it but I cant do both b/c I cant find emmc for the device and tool to repair emmc.

Any help plz.....

AutoResponder
Verified Account

609

03-11-2023, 05:07 AM

#2

Thank you for reaching out for support. Due to high demand, our free support services may experience some delays in response time. We apologize for any inconvenience this may cause.
Alternatively, we offer private support where you can receive dedicated attention and prompt support. These sessions are designed to provide personalized solutions to your specific needs.
If you are interested in scheduling a private session, please visit https://www.hovatek.com/remote

kelvinchinedu
Contributor

1,403

07-11-2023, 10:15 PM

#3

Use bye pass with flashtool

Mikesew1320
Junior Member

30

08-11-2023, 01:23 PM

#4

(07-11-2023, 10:15 PM)kelvinchinedu Use bye pass with flashtool

I don't get it. What do you mean by bye pass with flashtool? Is it a software like Miracle box? Can you tell me the details a little bit please? Am super ultra pro noob on tis stuffs.

Mikesew1320
Junior Member

30

08-11-2023, 05:45 PM

#5

(03-11-2023, 05:07 AM)AutoResponder Thank you for reaching out for support. Due to high demand, our free support services may experience some delays in response time. We apologize for any inconvenience this may cause.
Alternatively, we offer private support where you can receive dedicated attention and prompt support. These sessions are designed to provide personalized solutions to your specific needs.
If you are interested in scheduling a private session, please visit https://www.hovatek.com/remote

I followed the guide here and now I can flash all the partitions except super using Miracle Box Thunder 2.82 crack from hovatek. When super partition flashing started, It isn't killing Miracle tis time, Just Write error appears.

One think I remembered now is before the phone brcomes dead what I have done is......

1st I unlocked the bootloader.
2nd I Flashed empty vbmeta, twrp and modded lk.img and does a reboot[Before flashing Magisk] and here the device directly goes to fastboot mode when I reboot and later it becomes dead.

Mikesew1320
Junior Member

30

11-11-2023, 02:55 AM

#6

(07-11-2023, 10:15 PM)kelvinchinedu Use bye pass with flashtool

I followed the guide here and now I can flash all the partitions except super using Miracle Box Thunder 2.82 crack from hovatek. When super partition flashing started, It isn't killing Miracle tis time, Just Write error appears.

One think I remembered now is before the phone brcomes dead what I have done is......

1st I unlocked the bootloader.
2nd I Flashed empty vbmeta, twrp and modded lk.img and does a reboot[Before flashing Magisk] and here the device directly goes to fastboot mode when I reboot and later it becomes dead.

This post was last modified: 11-11-2023, 02:56 AM by Mikesew1320.

ryfoz
Senior Member

300

03-01-2024, 09:09 AM

#7

(07-11-2023, 10:15 PM)kelvinchinedu Use bye pass with flashtool

Pls I am finding it hard to post thread saying I don't have permission, pls I need help with my gionee device

View a Printable Version

Users browsing this thread:
1 Guest(s)

Find us

Call us

Mail us

Useful Links

Actions