Hovatek Forum

Full Version: help unbrick tecno ca7
You're currently viewing a stripped down version of our content. View the full version with proper formatting.
i was trying to follow this tutoria  https://www.hovatek.com/forum/thread-290...pid175195l  today and i bricked my phone when doing the first readback i followed every single step and i powered of my phone to do the read back but oops thats the last time i saw my phone.

the readback was not succesful cz i received this error ERROR:_STATUS_BROM_CMD_STARTCMD_FAIL_(0xC00600001)
I used the first custom Da for tecno camon x these were the softwares i used
1) wwr_2.51_eng
2)sp flash tool 5.1820
3)tecno ca7 DA 
4) had installed drivers with auto driver install and configured the as MEDIATEK DA USB VCOM DRIVER
i am using windows 10 and i have also tried to flash on windows 7 and that the same error
again one thing i have also noted is that my phone doesnt disconect itself from the pc as much as its plugged in its connected as MEDIATEK DA USB VCOM PORT.
so somebody help me overcome this plz
(09-08-2019, 12:10 AM)Davie254 Wrote: [ -> ]...

the backup process was interrupted, refer to https://www.hovatek.com/forum/thread-808.html
(09-08-2019, 12:10 AM)Davie254 Wrote: [ -> ]i was trying to follow this tutoria  https://www.hovatek.com/forum/thread-290...pid175195l  today and i bricked my phone when doing the first readback i followed every single step and i powered of my phone to do the read back but oops thats the last time i saw my phone.

the readback was not succesful cz i received this error ERROR:_STATUS_BROM_CMD_STARTCMD_FAIL_(0xC00600001)
I used the first custom Da for tecno camon x these were the softwares i used
1) wwr_2.51_eng
2)sp flash tool 5.1820
3)tecno ca7 DA 
4) had installed drivers with auto driver install and configured the as MEDIATEK DA USB VCOM DRIVER
i am using windows 10 and i have also tried to flash on windows 7 and that the same error
again one thing i have also noted is that my phone doesnt disconect itself from the pc as much as its plugged in its connected as MEDIATEK DA USB VCOM PORT.
so somebody help me overcome this plz

Once the phone comes up, try the second DA
(09-08-2019, 12:10 AM)Davie254 Wrote: [ -> ]i was trying to follow this tutoria  https://www.hovatek.com/forum/thread-290...pid175195l  today and i bricked my phone when doing the first readback i followed every single step and i powered of my phone to do the read back but oops thats the last time i saw my phone.

the readback was not succesful cz i received this error ERROR:_STATUS_BROM_CMD_STARTCMD_FAIL_(0xC00600001)
I used the first custom Da for tecno camon x these were the softwares i used
1) wwr_2.51_eng
2)sp flash tool 5.1820
3)tecno ca7 DA 
4) had installed drivers with auto driver install and configured the as MEDIATEK DA USB VCOM DRIVER
i am using windows 10 and i have also tried to flash on windows 7 and that the same error
again one thing i have also noted is that my phone doesnt disconect itself from the pc as much as its plugged in its connected as MEDIATEK DA USB VCOM PORT.
so somebody help me overcome this plz
Then why you readback for backup ROM since the official firmware for your phone available on internet?
you might do the backup procedure with WWR and ReadBack your firmware with spft tools if you can't or hard to find your official firmware on internet.